Replace headlight and taillight bulbs

Swap a burned-out headlight, brake light, or turn-signal bulb yourself: find the right bulb number, avoid touching halogen glass, and check your aim.

Easy 15–45 min · 5 min read

A dead headlight or brake light is one of the easiest fixes on a car and a common reason drivers get pulled over. On most vehicles it’s a 15-minute job. On some newer cars the bulb hides behind the bumper cover or wheel-well liner, and many late-model cars have sealed LED lights with no bulb to replace at all. Here’s how to tell which situation you’re in and do the job right.

Before you start: identify the bulb

Every replaceable bulb has a number: common headlight bulbs include H11, H7, H4, 9005, 9006, and 9012; common tail, brake, and signal bulbs include 3157, 7443, 1156, and 194. Your owner’s manual lists the exact bulb for each position, and most parts store websites have a lookup by year, make, and model. You can also read the number off the base of the old bulb once it’s out.

Check whether your car uses halogen, HID (xenon), or factory LED headlights. HID bulbs have a part number starting with “D” (D1S, D2R, D3S and so on) and usually come with a ballast box nearby. Factory LED headlights generally aren’t serviceable as a bulb — if an LED segment is out, the whole module or headlight assembly is usually replaced.

Safety: HID headlights run on a ballast that can produce tens of thousands of volts at startup. Turn the headlights and ignition off, remove the key or fob from the car, and let the system sit for a few minutes before touching an HID bulb or its connector. Never handle an HID bulb with the lights on. Bulbs also get hot enough to burn you — let them cool for at least 10 minutes after use.

Step-by-step: headlight bulb

  1. Turn everything off. Ignition off, headlight switch off, and on HID cars, key away from the vehicle.
  2. Find your access route. Open the hood and look behind the headlight housing. On many cars you’ll see a round rubber dust cover or a twist-off cap. If there’s no room, the manual may tell you to turn the steering wheel and go through an access flap in the wheel-well liner, or to remove the headlight housing (often two to four bolts plus a few bumper-cover fasteners).
  3. Disconnect the wiring. Press the release tab on the connector and pull it straight off. Don’t yank on the wires. If it’s stuck, a trim tool can help release the tab.
  4. Remove the bulb. Most modern bulbs twist about a quarter turn counterclockwise and pull out. Some older designs (H4, H7 in certain housings) are held by a wire spring clip you squeeze and swing aside.
  5. Install the new bulb without touching the glass. Hold it by the plastic or metal base only, wearing clean gloves. Seat it fully, matching the tabs to the notches, and lock it in.
  6. Reconnect and test. Plug the connector back in, optionally with a thin smear of dielectric grease on the terminals to keep out moisture, then test low and high beams before you reinstall dust covers or panels.
  7. Close it up. Reinstall the dust cap firmly; a loose cap lets moisture fog the housing.

Shop tip: Replace headlight bulbs in pairs. Halogen bulbs dim and yellow with age, so a new bulb next to an old one gives you an uneven beam — and the other side is usually not far behind. Buying a two-pack saves you doing the job twice.

Why you never touch halogen glass

Halogen bulbs run extremely hot. Oil from your skin leaves a residue that creates a hot spot on the quartz glass, and that spot can make the bulb fail early or even crack. If you do touch it, wipe the glass with rubbing alcohol on a lint-free cloth and let it dry before installing.

Step-by-step: taillight, brake light, and turn signal

  1. Find the access. Open the trunk or hatch and look for a removable panel, trim cover, or carpet flap behind the light. Some cars use plastic thumb nuts; others hold the taillight assembly on with two or three bolts so the whole housing pulls out rearward.
  2. Remove the socket. Twist the bulb socket counterclockwise and pull it out of the housing.
  3. Swap the bulb. Wedge-base bulbs (7443, 194) pull straight out. Bayonet bulbs (1156, 1157) push in and twist to release. Match the new bulb exactly — a single-filament bulb in a dual-filament socket will give you a brake light with no running light, or vice versa.
  4. Test every function. Have a helper check running lights, brakes, turn signals, and reverse, or back up to a garage door or window and watch the reflection.

About LED “upgrades”

Plug-in LED bulbs are sold everywhere for halogen headlight housings. In the US, headlights must meet federal standard FMVSS 108, and an LED bulb in a housing designed for a halogen filament is generally not compliant. The light source sits in a different spot than the filament the reflector was designed around, so the beam scatters — bright up close, but it blinds oncoming drivers and lights the road worse. For brighter lights, a quality halogen bulb or a complete DOT-compliant headlight assembly is the legal route. LED tail and signal bulbs are less of a concern, but LED turn signals may “hyperflash” (blink fast) unless you add a load resistor or compatible flasher.

Check your aim

If you removed the headlight housing, check the aim afterward: park on level ground facing a wall at night and make sure the low-beam cutoffs sit slightly below headlight height and match side to side. Your manual gives the exact distance and spec.

Common mistakes

  • Touching halogen glass with bare fingers.
  • Forgetting the dust cover or seating it loosely, which lets moisture fog the lens.
  • Assuming the bulb is bad. If a new bulb doesn’t light, check the fuse and look for a corroded or melted connector.
  • Installing LED headlight bulbs in halogen reflectors and ending up with glare and a failed inspection.

When to bring it to a shop

Take it to a pro if your headlights are sealed LED units, if the job requires removing the front bumper cover and you’re not comfortable with clips and fasteners, if a new bulb still doesn’t work after you’ve checked the fuse, or if a connector is melted or burnt. A shop can also aim your headlights properly and replace a cracked or water-filled housing.