Drain, flush and refill your coolant

How to drain, flush and refill engine coolant: choosing a compatible coolant type, mixing with distilled water, and burping air out of the system.

Moderate 1.5–3 hours · 4 min read

Coolant does more than keep your engine from overheating. It also carries corrosion inhibitors that protect the radiator, water pump, heater core and head gasket, and those inhibitors wear out with time. Signs it is overdue include rusty, murky or sludgy coolant, a sweet smell, overheating, or poor cabin heat. Older green coolants were changed roughly every two years or 30,000 miles. Most modern long-life coolants go five years or 100,000–150,000 miles for the first change, often less after that. Your owner's manual has the interval for your car.

Safety: Never open a radiator cap or coolant reservoir on a hot engine. The system is under pressure and coolant above boiling can erupt and cause serious burns. Wait until the engine is completely cold — hours, not minutes. Coolant is poisonous and tastes sweet to pets and children. Clean up every spill, store old coolant in sealed containers, and take it to a recycling center or parts store that accepts it. Never pour it down a drain or on the ground.

Choose the right coolant

This is the step people get wrong most. Coolants use different inhibitor chemistries, and some do not play well together:

  • IAT (traditional green) — older vehicles.
  • OAT — long-life, such as GM's orange coolant.
  • HOAT and phosphated HOAT — used by many European, Chrysler, Ford and Asian makes; often yellow, pink, blue or turquoise.
  • Si-OAT — newer VW group and some others; often purple or pink.

Color is not a reliable guide. Different brands dye the same chemistry different colors, and the same color can mean different chemistries. Go by the specification in your owner's manual or on the reservoir — a manufacturer spec number or the factory coolant. "Universal" coolants exist, but mixing chemistries can reduce protection and in some cases cause gel or sludge, so use the specified type. Concentrate is mixed with distilled water, usually 50/50; tap water adds minerals that cause scale.

Step-by-step

  1. With the engine cold, park level and set the parking brake. Raise the front on ramps or jack stands only if you need access underneath.
  2. Remove the radiator cap or pressure cap on the reservoir to let air in so it drains faster.
  3. Place the drain pan under the radiator drain petcock, usually at the bottom corner. Open it. If there is no petcock or it is broken, remove the lower radiator hose clamp and pull the hose off instead.
  4. Let it drain completely. Note that draining the radiator usually removes only about half the coolant; the rest stays in the engine block and heater core. Some engines have block drain plugs if your manual calls for a full drain.
  5. Close the petcock or refit the hose, then flush: fill the system with distilled water, run the engine with the heater set to maximum heat until it reaches operating temperature and the thermostat opens, let it cool completely, then drain again. Repeat until the water drains nearly clear. Chemical flush products are usually unnecessary on a reasonably maintained system and must be rinsed out thoroughly if used.
  6. Calculate your system capacity from the manual. Since some water remains in the block, use concentrate to make up the right ratio, or simply refill with 50/50 premix if you drained mostly clear water — a hydrometer check afterward tells you where you landed.
  7. Fill slowly through the radiator neck or reservoir, as your system is designed. Open any bleeder screws on the thermostat housing or heater hoses until coolant, not air, comes out, then close them.
  8. Burp the air out. Attach a spill-free funnel to the filler neck, fill it partway, and start the engine with the heater on maximum. Let it idle as bubbles rise into the funnel. Gently squeezing the upper radiator hose helps push air out. Keep the funnel partly full. When the thermostat opens you may see a big burp and the level drop.
  9. Once bubbles stop and the upper hose is hot, shut the engine off, plug the funnel and remove it, then install the cap.
  10. Fill the reservoir to the COLD line. Check again after the next couple of drives, cold, and top off as air works its way out.

Shop tip: Air pockets are the number one reason a fresh coolant job overheats. Signs of trapped air include no heat from the vents, a temperature gauge that climbs or swings, and gurgling behind the dashboard. Many engines need the front of the car raised so the filler is the highest point in the system, and some — especially certain European and hybrid vehicles — need a specific bleed procedure or an electric pump run with a scan tool. Check your manual before you start.

Common mistakes

  • Opening the cap hot.
  • Choosing coolant by color rather than specification.
  • Using tap water or pure concentrate. Straight coolant actually transfers heat worse than a proper mix.
  • Not burping the air out, then overheating on the first highway drive.
  • Breaking a plastic petcock by forcing it. They are fragile; turn gently.
  • Leaving old coolant where pets can reach it.

When to bring it to a shop

If you find oil in the coolant or coolant in the oil, white exhaust smoke with a sweet smell, constant coolant loss with no visible leak, or the engine keeps overheating after a careful refill, stop driving and get it diagnosed. Those can point to a failing head gasket, water pump or radiator, and an overheating engine can be destroyed in minutes.