Replace spark plugs

Replace your spark plugs the right way: cold engine, clearing the wells, checking gap, the anti-seize debate, correct torque and avoiding cross-threading.

Moderate 1–3 hours · 4 min read

Worn spark plugs make an engine feel tired: rough idle, hesitation when you accelerate, harder starting, a drop in fuel economy and, eventually, misfires with a flashing check-engine light. Replacement intervals vary widely. Old-style copper plugs were changed every 30,000 miles or so; most modern engines use iridium or platinum plugs rated for roughly 60,000 to 120,000 miles, with 100,000 being common. Your owner's manual lists the interval for your engine.

Safety: Work on a cold engine only. Spark plugs thread into aluminum cylinder heads, and removing them from a hot head can strip or pull the threads right out. A hot engine will also burn you. Disconnect the battery negative terminal if your manual recommends it, and never touch ignition coils or wires with the engine running — the voltage is high enough to hurt you.

Buy the right plugs

Use the exact plug your manufacturer specifies — brand and part number are in the owner's manual or available at the parts counter for your engine. Heat range, reach and seat type all matter. "Upgrading" to a different plug type rarely helps and can cause misfires. Most iridium and platinum plugs come pre-gapped, but you still check.

Checking the gap

The gap spec is in your manual or on an emissions label under the hood; many modern engines fall somewhere around 0.028–0.060 inch. Check each new plug with a wire-type gauge: it should slide through with slight drag. If adjustment is needed, bend only the ground strap, never the center electrode. Do not use a coin-style wedge gauge on fine-wire iridium or platinum plugs — prying against the tiny center tip can break it off. If an iridium plug is far out of spec out of the box, exchange it rather than bending it a lot.

Step-by-step

  1. Let the engine cool completely — ideally overnight.
  2. Remove the engine cover and anything blocking the coils. On some V6 engines, the rear plugs require removing the upper intake manifold; check your manual so you know what you are getting into.
  3. Work on one cylinder at a time so coils and wires never get mixed up.
  4. Unplug the coil connector (press the release tab — old connectors get brittle), remove the coil hold-down bolt, and twist and pull the coil straight up. For plug wires, pull on the boot, never the wire.
  5. Blow out the plug well with compressed air before removing the plug. Sand or debris that falls into the cylinder can score the cylinder wall. Wear eye protection.
  6. Loosen the plug with the spark plug socket and an extension. If it feels very tight or gritty, stop, add a little penetrating oil, let it soak, and work it gently back and forth.
  7. Look at the old plug. Light tan deposits are normal. Oily, black and sooty, or white and blistered plugs point to problems worth mentioning to a mechanic.
  8. Check the new plug's gap.
  9. Start the new plug by hand. Slip a short piece of rubber hose over the plug's top, drop it into the well and turn. The hose will slip if the plug tries to cross-thread. It should thread several full turns smoothly.
  10. Torque to spec (see below).
  11. Put a thin film of dielectric grease inside the coil boot, reinstall the coil, its bolt and the connector until it clicks.
  12. Repeat for each cylinder. Then reconnect the battery if you disconnected it, start the engine and confirm a smooth idle with no check-engine light.

Torque and the anti-seize debate

Over-tightening stretches the plug and can strip the head; under-tightening lets the plug overheat and can let it back out. Typical figures for a common 14 mm gasket-seat plug in an aluminum head are roughly 15–22 ft-lb, and tapered-seat plugs are much lower, often around 7–15 ft-lb — but check your owner's or service manual for your exact figure. If you do not have a torque wrench, the plug maker's angle method (printed on the box) is the next best thing: typically about a half to two-thirds turn past finger-tight for a new gasket plug, and much less for tapered seats.

As for anti-seize: major plug makers such as NGK say not to use it on their plated plugs, because the plating already prevents seizing and the lubricant lets the same torque stretch the plug further, risking breakage or stripped threads. Some manufacturers do specify it on specific engines. Follow the vehicle or plug maker's instruction. If you do use anti-seize, use a very small amount on the threads only and reduce the torque — commonly by around 20%.

Shop tip: Some engines are known for plugs that break or seize on removal, such as certain Ford 5.4L three-valve V8s. If you own one, look up the manufacturer's removal procedure and a special extractor before you start. And inspect each coil boot as it comes off — a cracked or carbon-tracked boot causes misfires that new plugs will not fix.

Common mistakes

  • Working on a hot engine and damaging aluminum threads.
  • Skipping the air blast and dropping debris into the cylinder.
  • Cross-threading by starting the plug with a ratchet instead of by hand.
  • Over-torquing, especially with anti-seize.
  • Gapping fine-wire plugs with a wedge gauge.
  • Mixing up plug wires or leaving a coil connector unclipped.
  • Dropping a plug. If a new one hits the floor, check the gap and porcelain again — a cracked insulator causes misfires.

When to bring it to a shop

If a plug will not come out, threads feel damaged, the job requires removing the intake manifold and you are not comfortable with that, or misfires continue after new plugs and coils, get professional help. Repairing stripped spark plug threads is a precise job, and a persistent misfire can damage your catalytic converter if ignored.