Replace the Engine Air Filter
Swap your engine air filter in about 15 minutes: how to find the airbox, inspect the old filter, seat the new one correctly and avoid common mistakes.
Your engine breathes thousands of gallons of air for every gallon of fuel it burns, and the air filter is what stands between that air and the inside of your engine. A clean filter keeps dust and grit from wearing cylinder walls and fouling sensors. Most manufacturers recommend replacing it somewhere between 15,000 and 30,000 miles, but if you drive on dusty roads, near construction or in heavy pollen, inspect it every oil change and replace it sooner. It's one of the easiest jobs on the car and usually needs no tools at all.
Before you start
Buy the filter that matches your exact year, make, model and engine — parts stores can look it up, and the box usually lists applications. Compare the new filter's shape to the old one before you leave the store if you can. Do this job with the engine off and cool; you'll be reaching around parts that get hot.
Safety: Make sure the engine is off and the key is out (or the push-button car is fully off) before reaching into the engine bay. Electric cooling fans can switch on by themselves even with the engine stopped on some cars. Never run the engine with the airbox open or the filter removed — anything sucked in, from a leaf to a stray screw, goes straight into the intake.
Step-by-step
- Find the airbox. Open the hood and follow the large plastic or rubber intake duct back from the throttle body. It leads to a black plastic box, usually near the front or side of the engine bay. That's the air filter housing.
- Note how it comes apart. Most housings close with metal spring clips you flip open by hand. Others use screws, hose clamps or a combination. Snap a quick photo with your phone so you remember how everything lined up, including any sensor wiring or small hoses attached to the lid.
- Open the housing. Release the clips or remove the screws. Keep screws in a cup — they love to drop into the engine bay. If the lid is attached to the intake duct, you may need to loosen the duct clamp to get enough room to lift it. Avoid pulling on the mass airflow (MAF) sensor wiring; unplug it if you need more slack.
- Remove the old filter. Lift it straight out and note which side faced up. Pay attention to how the rubber edge sat in the housing groove.
- Inspect it. Hold the filter up to a bright light or the sun. If light barely makes it through the pleats, or they're packed with dirt, bugs or leaves, it's due. A filter that's merely gray on the dirty side but still passes light may have life left, but at this price it's rarely worth stretching.
- Clean the housing. Vacuum or wipe out leaves, sand and debris from the lower half of the box. Do not blow it out with compressed air toward the intake side — you'll push dirt past where the filter sits. Cover the clean-side opening with a rag while you work if you're worried about dropping anything.
- Install the new filter. Set it in the same orientation as the old one, with the rubber sealing edge sitting evenly in its groove all the way around. Press gently along the edges so it's fully seated and not folded or pinched anywhere.
- Close it up. Lower the lid squarely, make sure it closes flush without forcing, then latch every clip or tighten every screw. Reconnect any duct clamps, hoses or sensor plugs you disturbed.
- Check your work. Run a finger around the seam — there should be no gaps. Start the engine and listen for any whistling or sucking noise around the housing, and make sure no warning lights come on.
Shop tip: If the old filter has a lot of leaves, seeds or a chewed corner, check the housing for a mouse nest or a cracked inlet snorkel. In South Florida we regularly find rodent nests and lizard debris in airboxes — catching it during a filter swap is a lot cheaper than an intake full of nesting material.
How it affects your car
On older carbureted cars, a clogged air filter could noticeably hurt fuel economy. On modern fuel-injected engines, the computer compensates for airflow, so the main symptoms of a badly restricted filter are reduced power at full throttle and sluggish acceleration rather than big mileage losses. Either way, a clean filter keeps abrasive dust out of the engine, which is the real point.
Common mistakes
- Filter not fully seated. A filter with a folded edge or a lid that isn't latched all the way lets unfiltered air bypass it entirely. That's worse than running an old filter.
- Forgetting a clip or screw. One open clip can let the lid lift and leak at the seam. Count them before and after.
- Leaving sensors unplugged. If you disconnected the mass airflow sensor or an intake air temperature sensor, forgetting to plug it back in will turn on the check engine light and the car may run poorly.
- Touching the MAF sensor. The tiny wire or film element inside the sensor is delicate. Never touch it or spray it with anything other than dedicated MAF sensor cleaner.
- Over-oiling reusable filters. If you use a washable, oiled cotton filter, too much oil can coat the MAF sensor and cause rough running. Follow the kit's directions exactly.
- Mixing it up with the cabin filter. They're different parts in different places. The engine filter is under the hood; the cabin filter usually lives behind the glove box.
When to bring it to a shop
If the housing is cracked, the clips are broken, the intake duct is torn, or you find oil in the airbox (which can point to crankcase ventilation problems), have a technician inspect it. The same goes if a check engine light or rough idle shows up after the swap and re-seating everything doesn't fix it — a cracked duct or disturbed sensor connection can be tricky to track down.