Check and Top Up the Fluids Under the Hood

Check engine oil, coolant, brake fluid, power steering, transmission and washer fluid in 15 minutes, and top them up safely with the right type.

Easy 15–20 min · 4 min read

A monthly look under the hood is the easiest way to catch a small leak before it turns into a big repair bill. Low oil can ruin an engine, low coolant can overheat it, and a dropping brake fluid level is often the first sign of worn pads or a leak. Checking everything takes about fifteen minutes. Do it once a month and before any long road trip.

Before you start

Park on level ground — a slope throws off every reading. For most checks the engine should be off and cool, ideally sitting overnight or for at least 30 minutes. A few cars want automatic transmission fluid checked hot with the engine running; your owner's manual will tell you. Most reservoirs are translucent plastic with MIN and MAX (or LOW and FULL) lines, and caps are often marked with a symbol and a color.

Safety: Never open the radiator cap or coolant reservoir cap on a hot engine. The system is under pressure, and coolant above its boiling point can spray out and cause serious burns. Wait until the engine is cool to the touch. Also: brake fluid strips paint fast. If you spill any on the body, wipe it immediately and rinse with plenty of water.

Step-by-step

1. Engine oil

  1. Find the dipstick — usually a yellow or orange loop handle.
  2. Pull it out, wipe it clean, push it all the way back in, then pull it out again.
  3. Read the level on both sides of the stick. It should be between the two marks (often dots, holes or a crosshatched area). The distance between them is typically about one quart.
  4. If it's low, add oil of the grade printed on the oil cap or in the manual, a half-quart at a time, wait a minute, and re-check. Don't go over the top mark.

Some newer cars have no dipstick and show the oil level in the instrument cluster menu instead. Follow the manual's procedure.

2. Coolant

  1. Find the translucent overflow or expansion tank connected to the radiator.
  2. With the engine cold, the level should sit between MIN and MAX (sometimes marked COLD and HOT).
  3. If low, top up with the coolant type your manual specifies, usually a 50/50 premixed product. Coolants differ in chemistry (OAT, HOAT, and others), and mixing incompatible types can cause gel or sludge.

Coolant that looks rusty, oily or has floating debris needs a professional look, not just a top-up.

3. Brake fluid

  1. The brake master cylinder reservoir is usually on the driver's side near the firewall. The cap lists the fluid type, commonly DOT 3 or DOT 4.
  2. Read the level through the side without opening it. It should be between MIN and MAX.
  3. Fresh fluid is clear to light amber; dark brown fluid is old and due for a flush.

Brake fluid level drops slowly as pads wear, which is normal. A noticeable drop between checks, or a level near MIN, means you should have your brakes inspected. If you do add some, wipe the cap clean first, use only the type on the cap from a sealed bottle (brake fluid absorbs moisture from the air), and replace the cap right away.

4. Power steering fluid

Many newer cars have electric power steering and no fluid at all. If yours has a reservoir (often with a steering wheel symbol on the cap), check it with the dipstick on the cap or the markings on the tank. Some are marked for both hot and cold readings. Use only the fluid type your manual specifies — some cars take ATF, others a dedicated power steering fluid.

5. Transmission fluid

Many modern automatics are "sealed" with no dipstick and must be checked by a technician with the car on a lift and at a specific temperature. If yours has a dipstick, follow the manual exactly — most call for the engine running, warmed up, in Park, on level ground. Healthy fluid is usually red or pink and doesn't smell burnt.

6. Windshield washer fluid

The reservoir cap usually shows a windshield-and-spray symbol. Fill it to near the top with washer fluid. Plain water works in a pinch, but proper fluid cleans better and resists algae growth.

Shop tip: Keep a small notebook or phone note with the date, mileage and how much of each fluid you added. If you're adding a quart of oil every month or topping coolant every week, that pattern tells a technician a lot more than "it seems low sometimes."

Common mistakes

  • Adding the wrong fluid to the wrong reservoir. Washer fluid in the coolant tank, or oil in the brake reservoir, causes real damage. Read the cap symbol every time. Petroleum-based fluids in the brake system ruin the rubber seals.
  • Reading the oil on a slope or right after shutdown. Oil needs a few minutes to drain back to the pan.
  • Overfilling. More is not better. Overfilled oil can foam, overfilled coolant just gets pushed out, and an overfilled brake reservoir can overflow when pads are replaced.
  • Using plain water as coolant. Fine as a roadside emergency, but water alone doesn't protect against corrosion or raise the boiling point. Get a proper coolant mix in soon.
  • Topping up and forgetting. If a fluid is low, it went somewhere. Look for drips under where you park.

When to bring it to a shop

Have the car inspected if any fluid drops noticeably between checks, if you see puddles under the car, if coolant looks milky or oil looks milky, if brake fluid is near MIN, or if transmission fluid smells burnt. A temperature gauge creeping up, a soft brake pedal or a brake warning light are reasons to stop driving and get help, not to keep topping up.