How to Change Your Engine Oil and Filter

Change your own engine oil and filter at home: draining, filter swap, crush washer, correct torque, refilling and checking the dipstick the right way.

Moderate 45–60 min · 5 min read

Fresh oil is the cheapest insurance your engine will ever get. Oil cools, cleans and cushions every moving part inside, and as it breaks down it does all three jobs worse. Most modern cars running synthetic oil call for a change somewhere between 5,000 and 10,000 miles (or every 6–12 months, whichever comes first), while older engines and severe-duty driving — short trips, heavy towing, stop-and-go traffic, extreme heat — may need it sooner. Your owner's manual or the car's oil-life monitor has the right interval for your engine.

Before you start

Look up three things in your owner's manual: the oil viscosity (for example 0W-20 or 5W-30), the oil capacity with filter, and the drain plug torque. Buy the right filter for your exact engine — filters that look alike can have different threads and bypass valves. Pick up a new crush washer for the drain plug too; they cost pennies and are designed to be used once.

Warm the engine for a few minutes so the oil flows freely, then shut it off and let it sit 5–10 minutes. You want oil that's warm, not scalding.

Safety: Never work under a car held up only by a jack. Lift on the manufacturer's jacking points, then lower the car onto jack stands rated for its weight (or drive onto ramps) on flat, solid ground, and chock the wheels that stay on the ground. Give the car a firm shove before you crawl under it. Hot oil and exhaust parts can burn you badly — wear gloves and keep your arms clear of the exhaust pipe.

Step-by-step

  1. Raise and secure the car. Park on level ground, set the parking brake, chock the rear wheels and lift the front onto stands or ramps. Keep it as level as you can so the oil drains completely and the dipstick reads accurately later.
  2. Open the oil fill cap. Loosening it lets air in so the oil drains faster.
  3. Locate the drain plug. It's a single bolt at the lowest point of the oil pan. Don't confuse it with the transmission drain plug, and remove any splash shield first.
  4. Drain the oil. Position the pan slightly off to the side — oil shoots out at an angle at first. Loosen the plug with a wrench, then spin it out by hand while pushing it in toward the pan so oil doesn't leak around the threads, and pull it away quickly. Let it drain until it slows to an occasional drip, usually 5–10 minutes.
  5. Clean and reinstall the drain plug. Wipe the plug and the pan's sealing surface. Remove the old crush washer (check that it didn't stick to the pan) and fit a new one. Thread the plug in by hand first to avoid cross-threading, then tighten to spec. Typical drain plug torque is roughly 20–30 ft-lb, but some are lower and aluminum pans are easy to strip, so check your service manual for your exact figure.
  6. Remove the old filter. Move the drain pan under the filter — it will dump another half-quart or so. Loosen it with a filter wrench and finish by hand. If you have a cartridge-style filter in a plastic housing on top of the engine, unscrew the cap and replace the element and the cap's O-ring instead.
  7. Check for the old gasket. Look at the filter mounting surface on the engine and make sure the old rubber gasket came off with the filter. This is the single most important check in the whole job (see "Common mistakes").
  8. Install the new filter. Wipe the mounting surface clean. Smear a thin film of fresh oil on the new filter's rubber gasket. If the filter mounts upright, you can pre-fill it partway with oil. Spin it on by hand until the gasket touches, then tighten another three-quarters of a turn by hand — or whatever the filter box says. Don't use the wrench to tighten it.
  9. Refill with oil. Lower the car to level ground. Using a funnel, pour in about a half-quart less than the listed capacity, then wait a minute for it to settle and check the dipstick.
  10. Check the level and top up. Pull the dipstick, wipe it, reinsert fully, pull it again and read it. Add oil in small amounts until it's at or just below the full mark. Don't overfill.
  11. Start and inspect. Reinstall the fill cap, start the engine and let it idle for 30–60 seconds. The oil pressure light should go out within a few seconds. Look under the car for drips at the plug and filter. Shut it off, wait a few minutes, and re-check the dipstick — the filter soaks up some oil, so you may need to add a little.
  12. Reset the oil-life monitor if your car has one (the procedure is in the owner's manual), and note the mileage.

Shop tip: Write the date and mileage on a strip of masking tape and stick it inside the driver's door jamb or on the windshield corner.

Common mistakes

  • The double gasket. If the old filter's gasket stays stuck to the engine and you spin the new filter on over it, it will seal for a few seconds and then blow out, dumping your oil on the road in under a minute. Always check the mounting surface.
  • Over-tightening the drain plug. Stripped oil pan threads turn a $40 oil change into a pan replacement. Use a torque wrench.
  • Reusing the crush washer. A flattened washer won't seal properly and leads to slow drips.
  • Overfilling. Too much oil can be whipped into foam by the crankshaft, which lubricates poorly and can damage seals and the catalytic converter. Trust the dipstick, not just the number on the bottle.
  • Dumping used oil. Pour it into the empty jugs and take it, along with the old filter, to an auto parts store or recycling center. Most accept it free.

When to bring it to a shop

If the drain plug is stripped or rounded, the filter is crushed and won't budge, you see metal flakes or a milky, coffee-with-cream look in the old oil, or the oil pressure light stays on after the change, stop and have a professional take a look. Milky oil can point to coolant getting into the engine, and a low-pressure warning is never something to drive on.