Jump-Start a Car the Right Way

Jump-start a dead battery safely with jumper cables or a portable jump pack: the correct connection order, where to ground, and what to do afterward.

Easy 10–20 min · 5 min read

A dead battery is one of the most common reasons a car won't start, and a jump-start can get you moving in minutes. You'll know it's likely the battery if you hear rapid clicking, a slow, weak crank, or nothing at all with dim or dead dash lights. Done correctly, jump-starting is safe and easy. Done in the wrong order, it can cause sparks, damage electronics or, in rare cases, make a battery explode. Batteries usually last three to five years, and heat shortens their life — if yours is older than that and keeps dying, it's probably time for a new one.

Before you start

Check your owner's manual first. Some vehicles have remote jump-start terminals under the hood (a positive post under a red cover and a designated ground point) because the battery is in the trunk or under a seat. Hybrids and EVs have their own rules: many can't be used as a donor at all, and some have special procedures for their 12-volt battery. Make sure both vehicles are the same system voltage — nearly all cars and light trucks are 12 volts.

Safety: Lead-acid batteries can give off hydrogen gas, which is explosive. Wear safety glasses, keep sparks, flames and cigarettes away, and never lean directly over the battery while connecting cables. Do not try to jump a battery that is cracked, leaking, bulging or frozen — call for help instead. Keep the cable clamps from touching each other or any metal once one end is connected. Remove rings and watches; a ring across a battery terminal can cause a severe burn.

Step-by-step with jumper cables

  1. Position the cars. Park the donor car close enough for the cables to reach, nose to nose or side by side, but make sure the vehicles do not touch. Put both in Park (or neutral with parking brake for a manual), set the parking brakes and turn both ignitions off. Turn off headlights, radio and climate controls in both.
  2. Identify the terminals. On each battery find positive (+, usually red, often with a red cover) and negative (−, usually black). If the terminals are heavily corroded with white or green crust, scrub them with a wire brush so the clamps get good contact.
  3. Red to the dead battery's positive. Clamp one red cable end securely to the positive terminal of the dead battery.
  4. Red to the donor battery's positive. Clamp the other red end to the positive terminal of the good battery.
  5. Black to the donor battery's negative. Clamp one black end to the negative terminal of the good battery.
  6. Black to bare metal on the dead car. Clamp the last black end to a clean, unpainted metal surface on the dead car's engine block or a designated ground point, away from the battery and away from moving parts like belts and the cooling fan. A thick bolt head or bracket on the engine works well. Making this final connection away from the battery means any spark happens away from battery gases.
  7. Start the donor car. Let it run for two to five minutes. A slightly raised idle helps put charge into the dead battery.
  8. Try to start the dead car. If it starts, great. If it only cranks slowly or clicks, wait a few more minutes and try again. Don't crank for more than 5–10 seconds at a time, and give the starter a minute to cool between attempts.
  9. Disconnect in reverse order. With both cars running, remove the black clamp from the ground point on the jumped car, then the black from the donor, then the red from the donor, then the red from the jumped car. Don't let clamps touch each other or the car while removing them.
  10. Keep the jumped car running. Drive it for at least 20–30 minutes, ideally at steady speeds, so the alternator can recharge the battery. Short trips and idling won't do much.

Using a portable jump starter

Compact lithium jump packs are worth having in any car. Most connect the same way — red clamp to the dead battery's positive, black clamp to unpainted metal ground or the negative terminal as the pack's instructions say — and many have reverse-polarity protection. Turn the pack on, start the car, then turn the pack off and remove the clamps black first. Keep the pack charged; check it every few months, since heat drains them faster.

Shop tip: Cheap, thin jumper cables are a false economy. Thin wire can't carry enough current to crank a big engine, and the clamps get hot. Look for 4- or 6-gauge cables at least 16 feet long — the lower the gauge number, the thicker the wire. And if your car needed a jump, get the battery and charging system tested soon; most parts stores will test them free.

Common mistakes

  • Reversing polarity. Connecting positive to negative can blow fuses, fry computer modules or damage the alternator. Double-check every connection before starting the donor.
  • Connecting the final black clamp to the dead battery's negative post. It usually works, but it puts the spark right next to the battery. Use a ground point.
  • Clamping to painted or plastic surfaces. Paint doesn't conduct; you'll get no jump. Find bare metal.
  • Letting the clamps touch. Once any clamp is on a battery, the free clamps are live.
  • Cranking endlessly. Long cranking overheats the starter. If it doesn't start after a few tries, something other than the battery may be the problem.
  • Shutting the car off right away. A deeply drained battery won't restart on its own after a two-minute drive.

When to bring it to a shop

If the car needs repeated jump-starts, the battery is more than four or five years old, the battery warning light stays on while driving, or the car still won't start after a good jump, have the battery, alternator and starter tested. A battery that keeps dying can also point to a parasitic drain — something drawing power with the car off — which takes proper testing equipment to track down.