Find and replace a blown fuse
Power outlet, radio, or wipers suddenly dead? Find the right fuse box, read the diagram, test the fuse, and replace it with the exact same amp rating.
When one thing on your car quits all at once — the power outlet, the radio, the wipers, one set of lights — a blown fuse is the first thing to check. It’s a cheap part, it takes minutes to swap, and you need almost no tools. The one rule you can’t bend: the new fuse must be the same amp rating as the old one. A fuse is a deliberate weak link that protects the wiring. If it blew, something drew too much current, and a bigger fuse just moves the failure into the wiring harness.
Where the fuse boxes are
Most cars have at least two fuse boxes, and many have three:
- Interior fuse panel — usually under the dashboard on the driver’s side, behind a kick panel near your left foot, or behind a cover on the end of the dash (visible when the driver’s door is open). It handles cabin items like the radio, power outlets, and interior lights.
- Underhood fuse/relay box — a black plastic box near the battery with a snap-on lid. It holds higher-current fuses and relays for things like the cooling fan, headlights, ABS, and starter.
- Trunk or under-seat boxes — some vehicles, especially larger SUVs and many European models, put an extra panel in the trunk or under a seat.
Your owner’s manual shows where each box is and includes a diagram of what every fuse powers. Many fuse box lids also have a diagram printed on the inside.
Safety: Turn the ignition off and switch off the circuit you’re working on before pulling or inserting a fuse. Don’t poke metal tools into fuse sockets, and never replace a fuse with foil, wire, or a higher-rated fuse — that’s how car fires start. The large fusible links and bolt-down main fuses near the battery carry very high current; leave those to a shop unless you know exactly what you’re doing, and disconnect the battery negative first if you must touch them. If your vehicle is a hybrid or EV, stay away from anything with orange high-voltage cabling.
Step-by-step
- Identify the circuit. Look up the dead component on the fuse diagram. Labels are often abbreviated (“CIG,” “ACC PWR,” “WIPER,” “RADIO”) and some fuses feed several items, which helps explain why two unrelated things quit at once.
- Find the fuse in the box. Match the diagram position to the box. Use a flashlight; the numbers molded into the box are tiny.
- Test before you pull (optional but faster). Blade fuses have two small metal test points exposed on top. With the ignition on, clip a test light to a good ground, then touch each test point. If both light up, the fuse is good. If only one does, it’s blown. If neither does, the fuse may only get power with the circuit switched on — or the problem is upstream.
- Pull the fuse. Use the plastic puller from the fuse box lid, or needle-nose pliers gripping the plastic body. Pull straight out.
- Inspect it. Hold it up to the light. A blown fuse has a broken or melted metal strip inside the plastic. Some failures are hard to see, so if you’re not sure, check continuity with a multimeter.
- Install the exact replacement. Match the type (standard, mini, low-profile mini, micro) and the amp rating stamped on top. Push it fully into the socket.
- Test the circuit. Turn the ignition on and try the device.
Reading fuse colors
Blade fuses are color-coded by amperage, and the colors are standardized for common types: tan is 5A, brown 7.5A, red 10A, blue 15A, yellow 20A, clear or natural 25A, and green 30A. The number stamped on top is what counts — always confirm it rather than going by color alone, especially with cartridge-style fuses, which use a different scheme.
Shop tip: Buy an assorted kit that matches your car’s fuse type and keep it in the glovebox, along with a printed or photographed copy of the fuse diagram. Many cars also have spare fuses clipped into the fuse box itself — check before you head to the store.
If the new fuse blows right away
A fuse that blows again immediately, or within a day or two, is telling you there’s a short or an overloaded circuit. Common causes:
- A coin or metal object dropped into a power outlet.
- A phone charger, dash cam, or inverter drawing more than the circuit is rated for.
- Chafed wiring touching metal — often in door hinges, trunk lid hinges, or behind a recently repaired bumper.
- A failing motor (wipers, blower, window) that’s binding and drawing excess current.
- Aftermarket accessories tapped into the wrong circuit.
Unplug accessories and try again. If it still blows, stop replacing fuses and find the short.
Common mistakes
- Installing a higher-amp fuse “so it won’t blow.” This is the single most dangerous fuse mistake.
- Pulling the wrong fuse because the diagram was read for a different trim or model year.
- Prying fuses with a screwdriver and cracking the fuse box terminals.
- Assuming the fuse is the problem when the real issue is a bad relay, switch, or ground.
- Forgetting that some fuses only have power with the ignition on, leading to a false “blown” reading on a test light.
When to bring it to a shop
Have a professional look at it if a fuse keeps blowing, if you see melted plastic or burn marks on the fuse box, if the main fuses or fusible links are involved, or if the problem started after collision damage or aftermarket wiring work. Tracking down a short takes wiring diagrams and patience, and it’s far cheaper than repairing a melted harness.