Check Tire Pressure and Tread Depth

Check tire pressure the right way with a gauge and measure tread depth with the penny test or a tread gauge so you know exactly when tires need replacing.

Easy 10–15 min · 4 min read

Your tires are the only parts of your car that touch the road, and two simple checks tell you most of what you need to know about them: pressure and tread depth. Underinflated tires run hot, wear their shoulders out early, hurt fuel economy and handle poorly. Worn tread can't push water out of the way, so the car hydroplanes and takes longer to stop in the rain. Check pressure at least once a month and before long trips, and look at your tread every time you check pressure.

Finding the right pressure

The correct pressure for your car is on a sticker (the tire placard) inside the driver's door jamb, and in the owner's manual. It's usually listed in PSI for front and rear, and sometimes for the spare. Most passenger cars fall somewhere around 30–36 PSI, but trucks, SUVs and some performance cars differ, so use your car's placard. The number molded into the tire sidewall is the maximum pressure the tire can hold — not the pressure you should run.

Safety: Never inflate a tire beyond the maximum pressure on its sidewall, and don't try to inflate a tire that's been run flat or has a visible bulge, cut or exposed cords — it can fail suddenly. If you're checking tires at the roadside or a gas station, stay aware of traffic and keep your body out of the lane.

Step-by-step: checking pressure

  1. Check them cold. Tire pressure rises as tires warm up from driving. For an accurate reading, check after the car has been parked for at least three hours, or has been driven less than a mile or so.
  2. Remove the valve cap and put it somewhere you won't lose it.
  3. Press the gauge onto the valve stem firmly and squarely. A brief hiss is normal; a continuous hiss means you're not seated straight. Read the gauge.
  4. Compare to the placard. If it's low, add air in short bursts and re-check. If it's high, press the small pin in the center of the valve with the gauge's nub or a fingernail to let air out, then re-check.
  5. Replace the valve cap. It keeps dirt and moisture out of the valve core.
  6. Repeat on all four tires — and the spare if it's accessible. A temporary compact spare often needs much higher pressure, commonly around 60 PSI. Check its sidewall or the placard.

About the TPMS light

Cars sold in the US since the 2008 model year have a tire pressure monitoring system (TPMS). The warning light typically comes on when a tire is roughly 25% below the recommended pressure — by which point it's already significantly underinflated. Don't use the light as your gauge. A steady light means at least one tire is low; a light that flashes for a minute or so at startup and then stays on usually means a fault in the system itself, like a dead sensor battery. On some cars the light goes out after a short drive once pressures are correct; others need a reset procedure described in the manual.

Step-by-step: checking tread depth

Tread depth is measured in 32nds of an inch. New passenger car tires typically start around 10/32" to 11/32". Most US states set the legal minimum at 2/32", but wet-road braking falls off well before that, which is why many tire makers and safety groups recommend replacing at 4/32" — especially where it rains hard.

  1. The penny test (2/32"). Put a penny upside down into a main tread groove with Lincoln's head facing you. If you can see the top of his head, the tread is at or below 2/32" and the tire needs replacing now.
  2. The quarter test (4/32"). Do the same with a quarter and Washington's head. If you can see the top of his head, you're at about 4/32" or less — time to start shopping.
  3. Use a tread depth gauge for real numbers. These cost a few dollars. Push the probe into a main groove, press the base flat against the tread blocks, and read the scale. Measure inside, center and outside grooves on each tire.
  4. Look at the wear bars. Molded into the bottom of the main grooves are small raised bars. When the tread is worn level with them, the tire is at 2/32".
  5. Read the wear pattern. Both edges worn more than the center suggests underinflation. Center worn more than edges suggests overinflation. One edge worn much more than the other, or a scalloped, choppy pattern, points to alignment or suspension issues.

Shop tip: Buy your own gauge and keep it in the glove box. Gas station gauges get dropped, run over and abused, and many read a few PSI off. A quality digital or dial gauge pays for itself the first time it catches a slow leak.

Common mistakes

  • Using the sidewall number. That's the maximum, not the target. Running at max pressure gives a harsh ride and less grip.
  • Checking hot tires and letting air out. A warm tire reads high. Let air out then and you'll be underinflated once it cools.
  • Waiting for the TPMS light. By the time it's on, the tire is already well below spec.
  • Forgetting seasonal changes. Pressure drops roughly 1 PSI for every 10°F drop in air temperature.
  • Checking only one groove. Uneven wear means the shallowest spot is what counts.
  • Ignoring tire age. Rubber ages even with good tread. Many manufacturers suggest inspection after about six years and replacement by ten years regardless — check the date code on the sidewall.

When to bring it to a shop

If a tire keeps losing air, has a bulge, a cut, a nail or screw in the tread, or shows uneven wear patterns, have it inspected. Punctures in the shoulder or sidewall can't be safely repaired. Uneven wear usually means an alignment or suspension problem that will eat your next set of tires too unless it's fixed.