Change a Flat Tire Safely
Change a flat tire safely: get off the road, use the factory jack correctly, mount the spare and tighten the lug nuts in a star pattern.
Sooner or later almost every driver gets a flat. Knowing how to swap in the spare calmly and safely can turn a ruined afternoon into a twenty-minute delay. The best time to learn is in your own driveway, not on the shoulder of a busy highway at night — so read through this, then find your jack and spare and do a dry run.
First: get somewhere safe
When you feel a tire go, don't slam on the brakes. Grip the wheel, ease off the gas, turn on your hazard lights and steer gently to a safe spot. Driving a short distance slowly on a flat to reach a wide, level shoulder, parking lot or exit ramp is far better than stopping in a travel lane or on a curve. You may ruin the tire or even the wheel, but those are cheaper than you.
Safety: If you can't get completely clear of traffic, can't find level, solid ground, or don't feel safe, stay in the car with your seatbelt on and hazards flashing and call roadside assistance or 911. Never put any part of your body under a car supported only by a jack — factory jacks are for lifting a wheel just enough to swap it, nothing more. Never start the engine while the car is on the jack.
Step-by-step
- Secure the car. Park on firm, level ground, shift into Park (or first gear on a manual), set the parking brake firmly and turn off the engine. Turn on the hazards and, if you have them, put reflective triangles 50 to 100 feet behind the car. Have passengers wait somewhere safe away from the road.
- Chock a wheel. Block the wheel diagonally opposite the flat, on both sides if you can, with wheel chocks or a heavy rock.
- Get out the spare and tools. They're usually under the trunk floor, though some trucks and SUVs hang the spare under the rear of the vehicle and lower it with a crank. Your owner's manual shows where everything is.
- Remove the hubcap if there is one, and loosen each lug nut about a half-turn counterclockwise while the tire is still on the ground. They may be tight. Position the wrench so you can push down on the handle with your foot or body weight; don't jerk it. Don't remove them yet.
- Position the jack. Find the jacking point closest to the flat — usually a reinforced notch or pinch weld on the rocker panel just behind the front wheel or just ahead of the rear wheel. Your manual and sometimes small arrows on the body mark the spot. Using the wrong place can crush the body or let the car slip.
- Raise the car. Crank the jack until the flat tire is about an inch or two off the ground — enough to fit the inflated spare, which is taller than the flat.
- Remove the lug nuts and the flat. Unscrew the nuts the rest of the way and keep them together in a pocket or the hubcap. Grip the tire at the sides and pull it straight toward you. Lay it flat on the ground, and slide it partly under the car next to the jack as a precaution.
- Mount the spare. Line up the holes with the studs and push the spare onto the hub until it sits flat. Thread every lug nut on by hand, tapered side facing the wheel if they're the cone type.
- Snug the nuts in a star pattern. Tighten them with the wrench in a crisscross order until they're snug, not fully tight. This pulls the wheel on evenly.
- Lower the car and tighten fully. Lower the jack until the tire carries the car's weight, remove the jack, then tighten each nut firmly in the same star pattern. Go around twice.
- Pack up. Stow the flat, jack and tools securely Pick up your triangles.
- Torque and check pressure soon. At the first chance, torque the lug nuts to your manufacturer's spec with a torque wrench (commonly about 76–100 ft-lb for passenger cars, more for trucks — check your owner's manual for your exact figure) and check the spare's air pressure.
Driving on a compact spare
Most cars carry a "temporary use only" compact spare, often called a donut. It's smaller, has a thinner tread and limited grip. Most are rated for about 50 mph and are meant for short distances — the exact limits are printed on the spare's sidewall or a sticker on the wheel, often along the lines of 50 mph and 50 to 70 miles. Compact spares usually need a much higher pressure than your regular tires, frequently around 60 PSI. Get the flat repaired or replaced as soon as possible, and expect ABS, traction control or AWD warnings on some vehicles while it's on.
Shop tip: If your car came with a tire inflator kit instead of a spare, read its instructions now. Sealant kits work for small punctures in the tread, but they can't fix sidewall damage, and the tire shop will need to clean the sealant out — tell them you used it so they can check the TPMS sensor too.
Common mistakes
- Trying to loosen lug nuts with the wheel in the air. The wheel just spins. Break them loose first, on the ground.
- Jacking on soft ground or a slope. The jack can sink or tip. If you must, put a flat board under the jack base.
- Forgetting the parking brake and wheel chock. A car rolling off a jack is one of the most dangerous things that can happen here.
- Tightening nuts in a circle, or fully tightening while the car is up. Use a star pattern, and do final tightening with the wheel on the ground.
- Never checking the spare. Spares lose air over the years like any tire. Check it a few times a year.
- Treating the donut as a real tire. Speed and distance limits are real; the tire can overheat and fail.
When to bring it to a shop
Have the flat tire inspected professionally. A puncture in the tread from a nail or screw can often be repaired with a proper internal patch-plug, but damage to the sidewall or shoulder, or a tire that was driven on while flat, usually means replacement. If the wheel was bent, a lug stud broke, or the car pulls or vibrates after the swap, have the wheel, suspension and alignment checked too.