Replace cracked side-mirror glass

Replace a cracked side mirror without buying the whole housing: remove the old glass safely, move heated-mirror connectors, and snap in the new glass.

Easy 20–45 min · 4 min read

A cracked side mirror is more than a cosmetic problem — distorted or missing glass gives you a blind spot, and in many states it can get you a ticket. The good news is that if the housing and motor still work, you usually only need to replace the glass, which costs a fraction of a complete mirror assembly. On most cars the glass snaps onto a motorized adjuster behind it and comes off in minutes.

Get the right glass

Mirror glass isn’t one-size-fits-all. Before ordering, check:

  • Side. Driver’s and passenger’s glass are different shapes.
  • Curvature. In the US, the driver’s side is usually flat and the passenger’s side is convex — that’s why it says “Objects in mirror are closer than they appear.” Some cars use aspheric glass with a curved outer section. Match the original.
  • Heated. Heated mirrors have two electrical terminals on the back of the glass, and often a small heater symbol on the glass or the switch.
  • Blind-spot indicator. Some glasses have an icon that lights up when a car is in your blind spot. These need the correct glass with the matching window or built-in light.
  • Auto-dimming. Auto-dimming exterior mirrors contain a gel between two layers of glass and have extra wiring. These are pricier and must be an exact match.

Look up your vehicle by year, make, model, and trim, and compare the listing to your owner’s manual and the features of your current mirror.

Safety: Broken mirror glass is razor sharp and can shatter further when you pry it. Wear heavy gloves and safety glasses the entire time. Cover the cracked glass with tape before removal to hold the pieces together, and vacuum up fragments afterward. If the mirror has a puddle light or turn signal, keep the ignition off while handling connectors.

Step-by-step

  1. Tape the cracked glass. Cover the whole face with overlapping strips of wide masking or duct tape so it comes out in one piece.
  2. Tilt the glass for access. If the power adjuster still works, tilt the glass fully inward (toward the car) so the outer edge sticks out. On manual mirrors, push the inner edge in by hand.
  3. Warm adhesive-mounted glass. If your glass is glued to a backing plate or the motor (common on some older and import models), warm it with a hair dryer or heat gun on low for a minute to soften the adhesive.
  4. Release the glass. Slide a plastic trim tool behind the outer edge and pry gently and steadily outward. On most clip-on designs, the backing plate pops off the adjuster with a firm snap. Work slowly and don’t lever against the painted housing.
  5. Disconnect the wires. If the mirror is heated or has a blind-spot indicator, you’ll see wires attached to the back. Gently pull the spade connectors off the terminals by their metal ends — don’t pull on the wire itself. Note which connector went where if there are more than two.
  6. Clean the mount. Remove any glass fragments from the housing and adjuster. Vacuum the area.
  7. Connect the new glass. Push the heater and indicator connectors onto the new glass’s terminals. Heater terminals generally aren’t polarity-sensitive, but indicator connections may be, so match them as they were.
  8. Snap it on. Line up the clips on the new backing plate with the adjuster. Press firmly in the center with your palm (through a towel for extra protection) until you hear it click. For adhesive-mounted glass, apply new double-sided tape as the instructions direct and press it firmly in place.
  9. Test. Adjust the mirror through its full range with the power switch, turn on the rear defrost to check the heater (it usually activates together), and verify the blind-spot light if equipped.

Shop tip: Clip-on mirror glass that’s been in the sun for years can be brittle. Do this job on a warm day or warm the housing first — cold plastic clips snap. And don’t push on the edge of the new glass to seat it; press in the center, right over the adjuster clips, or you can crack your brand-new mirror.

Common mistakes

  • Ordering the wrong curvature or a non-heated glass for a heated mirror.
  • Prying against the painted housing and scratching or cracking it.
  • Yanking the glass off and tearing the heater wires out of the mirror.
  • Forgetting to transfer the heater or indicator connectors before snapping the glass on.
  • Pressing on the edge instead of the center and cracking the new glass.
  • Working without gloves on broken glass.

When to bring it to a shop

If the mirror housing is cracked, the adjuster motor doesn’t move, the mirror folds poorly, or the cover is hanging loose, you likely need a complete mirror assembly. On many newer vehicles, the side mirror also houses cameras for surround-view systems, blind-spot sensors, or lane-change aids. Replacing those assemblies may require calibration of the camera system, so have a shop handle it to make sure your driver-assist features work correctly.