Touch up paint chips and small scratches

Find your paint code, prep the chip, and dab in factory-matched touch-up paint in thin layers to stop rust and make rock chips nearly disappear.

Easy 30–60 min plus drying time · 4 min read

Rock chips on the hood and nicks on door edges are part of driving, especially on highways. Left alone, a chip that goes down to bare metal will start to rust, and rust spreads under the paint. A touch-up won’t look like a professional refinish under close inspection, but done carefully it seals the metal and makes small chips hard to see from a few feet away. The secret is simple: dab, don’t brush, and build up thin layers.

Find your paint code

Don’t buy paint by color name — manufacturers use dozens of shades called “silver” or “white.” Your exact paint code is on a label, most often on the driver’s door jamb. Depending on the make, it may instead be under the hood, on the radiator support, inside the trunk lid, or in the glovebox (older GM vehicles used a “Service Parts Identification” sticker there). Your owner’s manual or a dealer parts counter can tell you where to look. Order touch-up paint by that code from the dealer or a reputable paint supplier.

Many modern colors are two-stage (a base color plus clear coat) or three-stage pearls. Two-stage colors need clear over the base to match the factory shine. Tri-coat pearl whites are the hardest to match with a touch-up; expect a slight difference.

Safety: Touch-up paints, primers, and grease removers contain solvents. Work in a ventilated area, wear nitrile gloves, keep them away from open flames, and don’t smoke nearby. Protect your eyes when using rust-removal pens or abrasive tools, since tiny fragments can fly.

Step-by-step

  1. Work in the right conditions. Shade, low wind, and temperatures roughly between 60°F and 85°F are ideal. Check the paint label for its range. Hot panels in direct sun make paint skin over too fast and trap bubbles.
  2. Wash and degrease. Wash the area with car soap, dry it, then wipe with wax and grease remover or isopropyl alcohol. Wax and road film keep paint from sticking.
  3. Deal with rust. If the chip shows orange or brown, remove the rust with a fiberglass pen or the tip of a fine rust-removal tool until you see bright metal. Keep the work inside the chip. Wipe clean again.
  4. Prime bare metal or plastic. If the chip is down to bare metal or plastic, dab in a tiny amount of touch-up primer and let it dry per the label.
  5. Shake the paint well. Metallic paints settle hard. Shake for at least a minute, then test the color on a hidden spot or a piece of paper held against the car.
  6. Dab, don’t brush. The brush in the bottle cap is usually too big. Instead, touch a toothpick or micro-applicator into the paint, wipe off the excess, and place a tiny drop in the center of the chip. Let it flow to the edges on its own. Never paint over the surrounding undamaged paint.
  7. Build thin layers. One drop won’t fill a chip. Let each layer dry (often 20–30 minutes; check the label) and add another until the paint is level with or just slightly above the surrounding surface.
  8. Add clear coat. For two-stage paint, let the color dry, then dab clear coat the same way. Fill just slightly proud of the surface.
  9. Let it cure. Wait at least a few days before washing and several weeks before waxing or polishing the spot, per the product instructions.

Shop tip: For a smoother finish, once the clear has fully cured you can level a raised blob with a touch-up leveling solution or very careful wet sanding with 2000–3000 grit on a tiny block, followed by polish. Go slowly — the factory clear around the chip is thin, and it’s easy to sand through it. If you’re unsure, leave the touch-up slightly raised; that looks better than a sand-through.

Scratches vs. chips

Run a fingernail across a scratch. If your nail doesn’t catch, it’s likely only in the clear coat, and polishing may remove it — touch-up paint will just make it more visible. If your nail catches and you see a different color (gray primer or silver metal) at the bottom, touch-up can help seal it. Fill long scratches with a fine applicator by drawing the paint along the bottom of the groove, not across the edges.

Common mistakes

  • Buying paint by color name instead of paint code.
  • Using the bottle brush and painting a wide blob over good paint.
  • Putting on one thick coat instead of several thin ones, leaving a sunken center or a raised ring.
  • Skipping degreasing, so the paint peels off at the first car wash.
  • Painting over rust, which keeps spreading under the new paint.
  • Working in direct sun or cold temperatures.
  • Skipping clear coat on a two-stage color, so the spot looks dull.

When to bring it to a shop

Touch-up is for chips and narrow scratches. If you have large areas of missing paint, peeling clear coat, rust bubbling under the paint, a long key scratch across several panels, or a tri-coat color that has to be invisible, a body shop can blend and refinish the panel for a factory-level result.