Replace brake pads and rotors

Step-by-step brake pad and rotor replacement: caliper removal, compressing pistons, rear screw-in calipers, torque, and bedding in new pads.

Moderate 1.5–3 hours per axle · 5 min read

Brakes tell you when they are tired. A high-pitched squeal when you brake is often the built-in wear indicator scraping the rotor. Grinding means the pad material is gone and metal is on metal. A pulsing pedal or a steering wheel that shakes under braking usually points to rotors with uneven thickness. Pads typically last anywhere from 25,000 to 70,000 miles depending on the car and how you drive, and rotors are commonly replaced alongside them. Do brakes one axle at a time — both front or both rear — never just one side.

Safety: Never work under a car held up only by a jack. Lift at the manufacturer's jacking points, set the car on rated jack stands, and chock the wheels that stay on the ground. Brake dust is nasty — do not blow it off with compressed air; use brake cleaner and wear a dust mask. Brake fluid is toxic and strips paint, so keep rags handy and wipe up spills immediately.

Inspect before you buy

Pull a wheel and look. Pads with less than about 3 mm (roughly 1/8 inch) of friction material are due. Check the rotor for deep grooves, a raised lip at the outer edge, blue heat spots or cracks. Every rotor has a minimum thickness stamped on it, often on the hat or edge — measure with a micrometer or caliper, and if it is at or below that number, it gets replaced, not resurfaced.

Step-by-step

  1. With the car on the ground, break the lug nuts loose about a half turn. Then jack up the car, set it on jack stands and remove the wheels.
  2. Open the hood and look at the brake fluid reservoir. If it is filled to the top, siphon a little out — pushing the pistons back raises the level and can overflow it onto your paint.
  3. Remove the caliper guide-pin bolts (commonly 12–17 mm or a hex/Torx bit). Swing or slide the caliper off the pads.
  4. Hang the caliper from the spring or strut with a bungee or wire. Never let it dangle by the rubber brake hose, and never step on the brake pedal with the caliper off.
  5. Remove the old pads and the abutment clips. Then remove the two caliper bracket bolts — these are much tighter — and take the bracket off.
  6. Remove the rotor. Some have small retaining screws (often seized; an impact driver helps). A stuck rotor can be persuaded with a few firm hammer blows on the hat area, not the braking surface.
  7. Clean the hub face thoroughly with a wire brush. Rust here causes runout, which causes the very pulsation you are trying to fix.
  8. Clean the new rotor's anti-rust coating off with brake cleaner (unless the box says it is a coating meant to stay), then install it and any retaining screw.
  9. Clean the bracket, install the new abutment clips, and put a thin film of high-temperature brake lubricant where the pad ears slide. Clean and re-grease the guide pins with the lubricant specified for rubber boots (silicone-based is typical).
  10. Reinstall the bracket and torque the bolts to spec. Bracket bolts are commonly in the 60–130 ft-lb range depending on the vehicle; some makers call for new bolts or threadlocker. Check your service manual.
  11. Compress the caliper piston. On most front calipers, a C-clamp or piston tool pushing an old pad against the piston does the job — go slowly and watch the reservoir.
  12. Install the new pads (note any wear indicator position and inner/outer pad differences), fit the caliper and torque the guide-pin bolts, typically 20–35 ft-lb.
  13. Mount the wheel, lower the car and torque lug nuts in a star pattern. Typical cars run 76–100 ft-lb; trucks and SUVs are often higher. Use your manual's figure.
  14. Pump the brake pedal until it is firm before you move the car. The first push will go to the floor because the pistons are retracted. Top up fluid to the MAX line.

Rear calipers with an integrated parking brake

Many rear calipers will not compress with a C-clamp — the piston must be screwed back in while pushed, using a wind-back tool that engages the notches in the piston face. Forcing it straight in destroys the internal mechanism. Line up the notches with the pin on the back of the pad when you finish. If your car has an electronic parking brake, the caliper motor must be retracted first using a scan tool or a dash-menu service mode; trying to force it can damage the motor. The service manual describes the procedure for your model.

Shop tip: Bed in the new pads before you trust them. On a safe, empty road, make about eight to ten moderate stops from around 35 mph down to 5 mph without coming to a full stop, then a few firmer stops from about 45 mph. Drive a few minutes without braking to let things cool, and avoid sitting at a light with the pedal held hard on hot rotors. This lays down an even film of pad material and prevents the vibration people blame on "warped" rotors. Follow the pad maker's bedding instructions if they differ.

Common mistakes

  • Forgetting to pump the pedal before driving. The first stop will have no brakes.
  • Grease on the pad or rotor surface. Lubricant goes on the contact points only. Clean fingerprints off rotors with brake cleaner.
  • Letting the caliper hang by its hose, which damages the hose internally.
  • Skipping the hub cleanup, leaving rust that causes pulsation in a few hundred miles.
  • Using an impact gun on lug nuts without a final torque wrench pass. Uneven lug torque distorts rotors.
  • Reusing seized guide pins or skipping new hardware clips — a sticking caliper wears pads unevenly and fast.

When to bring it to a shop

If a bleeder or bracket bolt is seized or rounded, a caliper piston will not retract or leaks fluid, the pedal stays soft after pumping, the car pulls to one side, or your vehicle has an electronic parking brake you cannot put into service mode, have a professional finish the job. Brakes are not the place to guess.