Bleed your brakes
How to bleed or flush brake fluid at home: choosing DOT 3, 4 or 5.1 fluid, the correct bleeding order, two-person and one-person methods, and ABS caveats.
A soft or spongy brake pedal, a pedal that sinks closer to the floor than it used to, or fluid that has turned dark brown are all signs your brake system needs bleeding. Brake fluid is hygroscopic — it absorbs moisture from the air over time. That water lowers the boiling point, so hard braking can boil the fluid and turn your pedal to mush, and it also corrodes the expensive parts inside the system. Most manufacturers recommend replacing brake fluid every two to three years. You also must bleed any time the system has been opened, such as after replacing a caliper or hose.
Pick the right fluid
The correct type is printed on the reservoir cap and in your owner's manual. DOT 3, DOT 4 and DOT 5.1 are all glycol-based and can technically be mixed, but use what the car calls for. DOT 5 is silicone-based and is never mixed with the others — it is used mostly in some classic and military vehicles. Buy fresh, sealed bottles; an opened bottle that has sat on the shelf for months has already soaked up moisture.
Safety: Brake fluid strips paint fast and is toxic. Cover fenders with old towels, keep a rag under every bleeder, and rinse any spill off paint with plenty of water immediately. Wear gloves and eye protection. Support the car on jack stands if you need to remove wheels, and never get under a car held only by a jack. Do not drive the car until you have a firm, high pedal.
Bleeding order
The traditional rule is to start at the wheel farthest from the master cylinder and work toward the nearest. On a left-hand-drive car that usually means right rear, left rear, right front, left front. However, many vehicles with diagonally split systems or certain ABS units use a different sequence. Check your service manual for your exact order — it matters.
Step-by-step (two-person method)
- Clean the area around the reservoir cap so dirt does not fall in when you open it.
- If you are doing a full flush, use a turkey baster to suck most of the old, dark fluid out of the reservoir — do not let it go below the ports in the bottom. Refill with fresh fluid to MAX.
- Get access to the first bleeder screw, usually on the back or top of the caliper or wheel cylinder. Remove the rubber cap and clean the bleeder with brake cleaner.
- Put the box-end wrench on the bleeder first, then push the clear tube onto the nipple and route it into the catch bottle with a little fresh fluid in the bottom so the tube end stays submerged.
- Have your helper press the pedal slowly and firmly, then hold it down.
- Open the bleeder about a quarter to a half turn. Fluid and air bubbles flow into the bottle and the pedal sinks.
- Close the bleeder before your helper lets the pedal up. Then they release it slowly.
- Repeat until the fluid in the tube runs clear and bubble-free — for a flush, until the color changes from old dark fluid to clean new fluid.
- Check the reservoir every few pumps. If it runs dry, you pull air into the master cylinder and have to start over.
- Snug the bleeder — they are small and easy to snap. Typical torque is only around 5–10 ft-lb. Refit the cap and move to the next wheel in sequence.
- When all four are done, top the reservoir to MAX, check the pedal with the engine off and on, and look for leaks at every bleeder.
Working alone
A one-way check-valve bleeder hose, or simply keeping the tube end submerged in fluid in the bottle, lets you open the bleeder and pump the pedal yourself without drawing air back in. Vacuum bleeders work well too, though they can pull air past the bleeder threads and show bubbles that are not really in the system. Pressure bleeders that pressurize the reservoir are the fastest one-person method and what most shops use.
Shop tip: On an older car that has never had a flush, do not let your helper push the pedal all the way to the floor. That moves the master cylinder seals into a section of bore they normally never touch, where corrosion and crud can tear them. Put a block of wood under the pedal or ask for a normal-length stroke. And if a bleeder is seized, soak it in penetrating oil and use a six-point wrench — a snapped bleeder turns a one-hour job into a caliper replacement.
About ABS
In most cases, a normal fluid flush on an ABS-equipped car works fine with the methods above, because the fluid passes through the ABS unit on its way to the wheels. The trouble comes if air gets into the ABS modulator — typically from letting the reservoir run dry or replacing the master cylinder or ABS unit. Then the valves often need to be cycled with a scan tool that can run the ABS bleed routine. If your pedal stays soft after a careful bleed, that is a likely reason.
Common mistakes
- Letting the reservoir run dry partway through. Keep checking it.
- Mixing DOT 5 silicone with glycol fluid, or reusing old fluid from the bottle.
- Wrong sequence for your vehicle.
- Releasing the pedal with the bleeder open, which sucks air right back in.
- Over-tightening bleeders until they snap.
- Leaving fluid on paint or rubber parts.
When to bring it to a shop
If the pedal is still soft after bleeding, the ABS light is on, a bleeder is seized, you find a leak at a line or hose, or the reservoir ran dry on an ABS car, have it looked at by a professional with a pressure bleeder and a scan tool. A low, soft pedal is never something to drive on.